CVE-2026-99751

Published Nov 20, 2026

Description

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix skb_pull() BUG in __bpf_redirect_neigh() The issue: This is a follow-up to the short link-layer header fixes from Eric. After vlan pop_eth, a privileged SCHED_ACT BPF program can call bpf_skb_change_head(skb, 1, 0) and then bpf_redirect_neigh(). __bpf_redirect_neigh() calls skb_pull(skb, sizeof(*ethh)) after checking only that mac_header < network_header. Nothing verifies that the MAC header is long enough, that it is linear, or that the IP header the redirect goes on to read is linear either. A SCHED_ACT BPF program can do: bpf_skb_change_head(skb, 1, 0); bpf_redirect_neigh(lo, NULL, 0, 0); after vlan pop_eth. The skb then has mac_len == 1 and only one byte of linear data; skb_pull(ETH_HLEN) trips the skb->len < skb->data_len BUG in __skb_pull(): kernel BUG at ./include/linux/skbuff.h:2839! RIP: skb_pull+0x40/0x50 Call Trace: skb_do_redirect -> packet_xmit -> packet_sendmsg Kernel panic - not syncing: Fatal exception in interrupt The v4 and v6 paths read ip_hdr() and ipv6_hdr() as soon as the MAC header is gone. On the AF_PACKET frame below that leaves headlen == 0 after the pull, so the network header sits at skb->tail and the route lookup reads ip4h->protocol, ip4h->saddr and ip4h->daddr past the linear area. The Fix: Use skb_network_offset(), which is the MAC header span, instead of skb->mac_len. mac_len is zero for locally generated tc egress and netkit packets, while the span still rejects the one-byte header produced by pop_eth + bpf_skb_change_head(skb, 1, 0). The single check also covers the mac_header >= network_header test it replaces. Use pskb_may_pull() to make the Ethernet header linear before it is read or pulled, and to make the IP header linear in both the v4 and the v6 path before ip_hdr()/ipv6_hdr() is read. The header pointers are taken after the pull, since pskb_may_pull() may reallocate skb->head. Conditions to recreate the bug: On x86-64 with 4 KiB pages, enable CONFIG_PACKET, CONFIG_BPF_SYSCALL, CONFIG_NET_SCH_INGRESS, CONFIG_NET_CLS_MATCHALL, CONFIG_NET_ACT_VLAN and CONFIG_NET_ACT_BPF. Run as root with BPF loading, network administration and raw-packet privileges. Bring lo up and attach a SCHED_ACT program that calls bpf_skb_change_head(skb, 1, 0), then returns bpf_redirect_neigh(skb->ifindex, NULL, 0, 0): ip link set lo up tc qdisc add dev lo clsact tc filter add dev lo egress matchall action vlan pop_eth pipe \ action bpf object-file neigh_chghead.o section action Send an untagged ETH_P_IP frame of ETH_HLEN + 8192 bytes through an AF_PACKET/SOCK_RAW socket bound to lo, without PACKET_VNET_HDR or PACKET_QDISC_BYPASS. Use a unicast destination MAC. The sender's skb has a 14-byte linear Ethernet prefix and a fragmented payload; pop_eth removes that prefix and change_head restores only one linear byte. The unfixed neighbor redirect then tries to pull 14 bytes and BUGs. Sending the same frame without pop_eth and change_head leaves the IP header in the frags, which is the route lookup reading past skb->tail.

Is your site exposed to CVE-2026-99751?

Run a free security scan — no signup, results in seconds.

EPSS — Exploit Prediction

0.0018
Probability of exploitation
0.07%
Percentile rank

EPSS estimates the probability that this vulnerability will be exploited in the wild within the next 30 days. A higher score means more likely to be exploited.

References

Frequently Asked Questions

What is CVE-2026-99751? +
In the Linux kernel, the following vulnerability has been resolved: bpf: Fix skb_pull() BUG in __bpf_redirect_neigh() The issue: This is a follow-up to the short link-layer header fixes from Eric. After vlan pop_eth, a privileged SCHED_ACT BPF program can call bpf_skb_change_head(skb, 1, 0) and then bpf_redirect_neigh(). __bpf_redirect_neigh() calls skb_pull(skb, sizeof(*ethh)) after checking only that mac_header < network_header. Nothing verifies that the MAC header is long enough, that it is linear, or that the IP header the redirect goes on to read is linear either. A SCHED_ACT BPF program can do: bpf_skb_change_head(skb, 1, 0); bpf_redirect_neigh(lo, NULL, 0, 0); after vlan pop_eth. The skb then has mac_len == 1 and only one byte of linear data; skb_pull(ETH_HLEN) trips the skb->len < skb->data_len BUG in __skb_pull(): kernel BUG at ./include/linux/skbuff.h:2839! RIP: skb_pull+0x40/0x50 Call Trace: skb_do_redirect -> packet_xmit -> packet_sendmsg Kernel panic - not syncing: Fatal exception in interrupt The v4 and v6 paths read ip_hdr() and ipv6_hdr() as soon as the MAC header is gone. On the AF_PACKET frame below that leaves headlen == 0 after the pull, so the network header sits at skb->tail and the route lookup reads ip4h->protocol, ip4h->saddr and ip4h->daddr past the linear area. The Fix: Use skb_network_offset(), which is the MAC header span, instead of skb->mac_len. mac_len is zero for locally generated tc egress and netkit packets, while the span still rejects the one-byte header produced by pop_eth + bpf_skb_change_head(skb, 1, 0). The single check also covers the mac_header >= network_header test it replaces. Use pskb_may_pull() to make the Ethernet header linear before it is read or pulled, and to make the IP header linear in both the v4 and the v6 path before ip_hdr()/ipv6_hdr() is read. The header pointers are taken after the pull, since pskb_may_pull() may reallocate skb->head. Conditions to recreate the bug: On x86-64 with 4 KiB pages, enable CONFIG_PACKET, CONFIG_BPF_SYSCALL, CONFIG_NET_SCH_INGRESS, CONFIG_NET_CLS_MATCHALL, CONFIG_NET_ACT_VLAN and CONFIG_NET_ACT_BPF. Run as root with BPF loading, network administration and raw-packet privileges. Bring lo up and attach a SCHED_ACT program that calls bpf_skb_change_head(skb, 1, 0), then returns bpf_redirect_neigh(skb->ifindex, NULL, 0, 0): ip link set lo up tc qdisc add dev lo clsact tc filter add dev lo egress matchall action vlan pop_eth pipe \ action bpf object-file neigh_chghead.o section action Send an untagged ETH_P_IP frame of ETH_HLEN + 8192 bytes through an AF_PACKET/SOCK_RAW socket bound to lo, without PACKET_VNET_HDR or PACKET_QDISC_BYPASS. Use a unicast destination MAC. The sender's skb has a 14-byte linear Ethernet prefix and a fragmented payload; pop_eth removes that prefix and change_head restores only one linear byte. The unfixed neighbor redirect then tries to pull 14 bytes and BUGs. Sending the same frame without pop_eth and change_head leaves the IP header in the frags, which is the route lookup reading past skb->tail.
How do I check if I'm vulnerable to CVE-2026-99751? +
You can use Secably's free Website Scanner to check your website for known vulnerabilities. For infrastructure scanning, use the Port Scanner to identify exposed services that may be affected. Check the vendor advisories linked above for specific patch and version information.

Don't wait for an exploit

Scan your website for vulnerabilities like CVE-2026-99751 — free, no signup required.

Patch and protect

Block known exploits with a web application firewall while you patch, keep your own devices clean, or test the fix on a fresh server.

Compare VPS prices →

Affiliate links: we may earn a commission, your price stays the same.