CVE-2026-99578

Published Nov 20, 2026

Description

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: usb: route bmc frames via the high queue only for DTIM delivery In AP mode every broadcast and multicast data frame is routed to TX_DESC_QSEL_HIGH, the after-DTIM queue, whether or not anybody is asleep. The firmware drains that queue at beacon pace, a dozen or so frames per second measured on RTL8822BU, while one associated client's mDNS/SSDP chatter alone exceeds that. The excess accumulates inside the chip until the shared TX page pool is exhausted (measured: 14 of 1803 pages left). From that point every host-sourced frame queues behind the backlog: authentication responses reach the air seconds after the client has given up, so no station can associate anymore, and the beacon reserved-page download fails the BCN_VALID poll ("error beacon valid") because it needs pages from the same pool. The AP keeps beaconing, so the failure looks like a silent RX stall and only a reboot recovers. mac80211 already decides when after-DTIM delivery is needed: it sets IEEE80211_TX_CTL_SEND_AFTER_DTIM on bmc frames only while at least one station is actually dozing. Honor that instead of routing unconditionally: flagged frames keep going through the high queue with the MORE_DATA and HGQMD handling introduced by commit 076f786a0ae1 ("wifi: rtw88: Fix AP mode incorrect DTIM behavior"), everything else leaves at line rate through the AC queues. This partially reverts the usb.c hunk of that commit, whose unconditional routing is what lets the backlog build up. On a bench AP (USB2, 20 MHz, WPA2, hostapd, a Windows client driven through disconnect/reconnect cycles): reconnects fail 0/5 on RTL8822BU and 0/3 on RTL8821CU before this change, and pass 10/10 and 5/5 with it, with the page pool staying healthy and no beacon errors logged.

Is your site exposed to CVE-2026-99578?

Run a free security scan — no signup, results in seconds.

EPSS — Exploit Prediction

0.0020
Probability of exploitation
0.10%
Percentile rank

EPSS estimates the probability that this vulnerability will be exploited in the wild within the next 30 days. A higher score means more likely to be exploited.

References

Frequently Asked Questions

What is CVE-2026-99578? +
In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: usb: route bmc frames via the high queue only for DTIM delivery In AP mode every broadcast and multicast data frame is routed to TX_DESC_QSEL_HIGH, the after-DTIM queue, whether or not anybody is asleep. The firmware drains that queue at beacon pace, a dozen or so frames per second measured on RTL8822BU, while one associated client's mDNS/SSDP chatter alone exceeds that. The excess accumulates inside the chip until the shared TX page pool is exhausted (measured: 14 of 1803 pages left). From that point every host-sourced frame queues behind the backlog: authentication responses reach the air seconds after the client has given up, so no station can associate anymore, and the beacon reserved-page download fails the BCN_VALID poll ("error beacon valid") because it needs pages from the same pool. The AP keeps beaconing, so the failure looks like a silent RX stall and only a reboot recovers. mac80211 already decides when after-DTIM delivery is needed: it sets IEEE80211_TX_CTL_SEND_AFTER_DTIM on bmc frames only while at least one station is actually dozing. Honor that instead of routing unconditionally: flagged frames keep going through the high queue with the MORE_DATA and HGQMD handling introduced by commit 076f786a0ae1 ("wifi: rtw88: Fix AP mode incorrect DTIM behavior"), everything else leaves at line rate through the AC queues. This partially reverts the usb.c hunk of that commit, whose unconditional routing is what lets the backlog build up. On a bench AP (USB2, 20 MHz, WPA2, hostapd, a Windows client driven through disconnect/reconnect cycles): reconnects fail 0/5 on RTL8822BU and 0/3 on RTL8821CU before this change, and pass 10/10 and 5/5 with it, with the page pool staying healthy and no beacon errors logged.
How do I check if I'm vulnerable to CVE-2026-99578? +
You can use Secably's free Website Scanner to check your website for known vulnerabilities. For infrastructure scanning, use the Port Scanner to identify exposed services that may be affected. Check the vendor advisories linked above for specific patch and version information.

Don't wait for an exploit

Scan your website for vulnerabilities like CVE-2026-99578 — free, no signup required.

Patch and protect

Block known exploits with a web application firewall while you patch, keep your own devices clean, or test the fix on a fresh server.

Compare VPS prices →

Affiliate links: we may earn a commission, your price stays the same.