CVE-2026-99547

Published Nov 19, 2026

Description

In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Do not RPM complete unrelated subtrees on unplug When a Thunderbolt device is unplugged, that switch and every switch subsequent to it on the bus device list is `complete()`d, not just its child devices. In the case of multiple domains, it may cause, eg, an attempt to `complete()` the uninitialized domain 1 root switch RPM completion on unplug of a switch from domain 0 (though ordering is not guaranteed numerically sorted). I initially noticed this issue on a Dell XPS9720 when the system would seem to sporadically not wake after unplugging a Thunderbolt dock. I tried multiple kernel versions including v7.2.7 and v7.3-rc4 to see if that resolved the issue, but the issue persisted. Eventually I found that I could consistently generate a kernel Oops reporting a page fault at 0xffff_ffff_ffff_fff8 on unplug from one side of the laptop and went bug hunting. I became suspicious of the `bus_for_each_dev()` walk that I ultimately ended up changing. To confirm this issue, I did an eBPF trace of `bus_for_each_dev()`, `complete_rpm()`, and `complete()` while unplugging in a variety of situations and found that an unplug from domain 0 tries to `complete_rpm()` domain 1's switch, whose RPM completion is not initialized and thus is holding a null wait-list pointer, triggering the page fault. Here are the key sections of that eBPF trace. Note that HEAD denotes the completion's own wait-list HEAD: ``` RESCAN_ENTER domain=0 COMPLETE rescan_domain=0 target=0-1 target_domain=0 route=0x1 parent=0-0 unplugged=1 COMPLETION done=0 head=HEAD next=HEAD prev=HEAD BUS_WALK domain=0 start=0-1 callback=complete_rpm CALLBACK_ENTER rescan_domain=0 dev=1-0 parent=domain1 is_switch=1 COMPLETE rescan_domain=0 target=1-0 target_domain=1 route=0x0 parent=domain1 unplugged=0 COMPLETION done=0 head=HEAD next=0 prev=0 complete+5 complete_rpm+43 bus_for_each_dev+133 icm_free_unplugged_children+250 icm_rescan_work+42 ``` This patch gates the `complete()` on an additional condition - that the Thunderbolt domain matches the domain of the device that was unplugged. I only have a single system with multiple Thunderbolt domains - the Dell XPS9720. I am consistently able to reproduce the Oops on that system. Since running with this patch, I have not seen the Oops reoccur. I have also tested it on a Thinkpad X1-Gen12, and that system boots and runs well with it, but it only has a single Thunderbolt domain, so it does not exercise the multi-domain failure case.

Is your site exposed to CVE-2026-99547?

Run a free security scan — no signup, results in seconds.

References

Frequently Asked Questions

What is CVE-2026-99547? +
In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Do not RPM complete unrelated subtrees on unplug When a Thunderbolt device is unplugged, that switch and every switch subsequent to it on the bus device list is `complete()`d, not just its child devices. In the case of multiple domains, it may cause, eg, an attempt to `complete()` the uninitialized domain 1 root switch RPM completion on unplug of a switch from domain 0 (though ordering is not guaranteed numerically sorted). I initially noticed this issue on a Dell XPS9720 when the system would seem to sporadically not wake after unplugging a Thunderbolt dock. I tried multiple kernel versions including v7.2.7 and v7.3-rc4 to see if that resolved the issue, but the issue persisted. Eventually I found that I could consistently generate a kernel Oops reporting a page fault at 0xffff_ffff_ffff_fff8 on unplug from one side of the laptop and went bug hunting. I became suspicious of the `bus_for_each_dev()` walk that I ultimately ended up changing. To confirm this issue, I did an eBPF trace of `bus_for_each_dev()`, `complete_rpm()`, and `complete()` while unplugging in a variety of situations and found that an unplug from domain 0 tries to `complete_rpm()` domain 1's switch, whose RPM completion is not initialized and thus is holding a null wait-list pointer, triggering the page fault. Here are the key sections of that eBPF trace. Note that HEAD denotes the completion's own wait-list HEAD: ``` RESCAN_ENTER domain=0 COMPLETE rescan_domain=0 target=0-1 target_domain=0 route=0x1 parent=0-0 unplugged=1 COMPLETION done=0 head=HEAD next=HEAD prev=HEAD BUS_WALK domain=0 start=0-1 callback=complete_rpm CALLBACK_ENTER rescan_domain=0 dev=1-0 parent=domain1 is_switch=1 COMPLETE rescan_domain=0 target=1-0 target_domain=1 route=0x0 parent=domain1 unplugged=0 COMPLETION done=0 head=HEAD next=0 prev=0 complete+5 complete_rpm+43 bus_for_each_dev+133 icm_free_unplugged_children+250 icm_rescan_work+42 ``` This patch gates the `complete()` on an additional condition - that the Thunderbolt domain matches the domain of the device that was unplugged. I only have a single system with multiple Thunderbolt domains - the Dell XPS9720. I am consistently able to reproduce the Oops on that system. Since running with this patch, I have not seen the Oops reoccur. I have also tested it on a Thinkpad X1-Gen12, and that system boots and runs well with it, but it only has a single Thunderbolt domain, so it does not exercise the multi-domain failure case.
How do I check if I'm vulnerable to CVE-2026-99547? +
You can use Secably's free Website Scanner to check your website for known vulnerabilities. For infrastructure scanning, use the Port Scanner to identify exposed services that may be affected. Check the vendor advisories linked above for specific patch and version information.

Don't wait for an exploit

Scan your website for vulnerabilities like CVE-2026-99547 — free, no signup required.

Patch and protect

Block known exploits with a web application firewall while you patch, keep your own devices clean, or test the fix on a fresh server.

Compare VPS prices →

Affiliate links: we may earn a commission, your price stays the same.