CVE-2026-93168

Published Sep 17, 2026

Description

In the Linux kernel, the following vulnerability has been resolved: dmaengine: xilinx_dma: Fix CPU stall in xilinx_dma_poll_timeout Currently when calling xilinx_dma_poll_timeout with delay_us=0 and a condition that is never fulfilled, the CPU busy-waits for prolonged time and the timeout triggers only with a massive delay causing a CPU stall. This happens due to a huge underestimation of wall clock time in poll_timeout_us_atomic. Commit 7349a69cf312 ("iopoll: Do not use timekeeping in read_poll_timeout_atomic()") changed the behavior to no longer use ktime_get at the expense of underestimation of wall clock time which appears to be very large for delay_us=0. Instead of timing out after approximately XILINX_DMA_LOOP_COUNT microseconds, the timeout takes XILINX_DMA_LOOP_COUNT * 1000 * (time that the overhead of the for loop in poll_timeout_us_atomic takes) which is in the range of several minutes for XILINX_DMA_LOOP_COUNT=1000000. Fix this by using a non-zero value for delay_us. Use delay_us=10 to keep the delay in the hot path of starting DMA transfers minimal but still avoid CPU stalls in case of unexpected hardware failures. One-off measurement with delay_us=0 causes the cpu to busy wait around 7 minutes in the timeout case. After applying this patch with delay_us=10 the measured timeout was 1053428 microseconds which is roughly equivalent to the expected 1000000 microseconds specified in XILINX_DMA_LOOP_COUNT. Add a constant XILINX_DMA_POLL_DELAY_US for delay_us value.

Is your site exposed to CVE-2026-93168?

Run a free security scan — no signup, results in seconds.

References

Frequently Asked Questions

What is CVE-2026-93168? +
In the Linux kernel, the following vulnerability has been resolved: dmaengine: xilinx_dma: Fix CPU stall in xilinx_dma_poll_timeout Currently when calling xilinx_dma_poll_timeout with delay_us=0 and a condition that is never fulfilled, the CPU busy-waits for prolonged time and the timeout triggers only with a massive delay causing a CPU stall. This happens due to a huge underestimation of wall clock time in poll_timeout_us_atomic. Commit 7349a69cf312 ("iopoll: Do not use timekeeping in read_poll_timeout_atomic()") changed the behavior to no longer use ktime_get at the expense of underestimation of wall clock time which appears to be very large for delay_us=0. Instead of timing out after approximately XILINX_DMA_LOOP_COUNT microseconds, the timeout takes XILINX_DMA_LOOP_COUNT * 1000 * (time that the overhead of the for loop in poll_timeout_us_atomic takes) which is in the range of several minutes for XILINX_DMA_LOOP_COUNT=1000000. Fix this by using a non-zero value for delay_us. Use delay_us=10 to keep the delay in the hot path of starting DMA transfers minimal but still avoid CPU stalls in case of unexpected hardware failures. One-off measurement with delay_us=0 causes the cpu to busy wait around 7 minutes in the timeout case. After applying this patch with delay_us=10 the measured timeout was 1053428 microseconds which is roughly equivalent to the expected 1000000 microseconds specified in XILINX_DMA_LOOP_COUNT. Add a constant XILINX_DMA_POLL_DELAY_US for delay_us value.
How do I check if I'm vulnerable to CVE-2026-93168? +
You can use Secably's free Website Scanner to check your website for known vulnerabilities. For infrastructure scanning, use the Port Scanner to identify exposed services that may be affected. Check the vendor advisories linked above for specific patch and version information.

Don't wait for an exploit

Scan your website for vulnerabilities like CVE-2026-93168 — free, no signup required.