CVE-2026-90591

HIGH
Published Nov 9, 2026 Modified Nov 12, 2026 CWE-787

Description

The NXP ENET-QOS Ethernet driver's receive work handler eth_nxp_enet_qos_rx() in drivers/ethernet/eth_nxp_enet_qos hands each processed descriptor back to the DMA by writing desc->read.control = rx_desc_refresh_flags, which sets OWN_FLAG and BUF1_ADDR_VALID_FLAG. RDES0 of a receive descriptor is the DMA buffer address in read format, but the hardware write-back aliases that word with the VLAN tag fields (or, for a context descriptor, the timestamp low word), so it is destroyed on every completion. The success path rewrites desc->read.buf1_addr before re-arming; the four drop paths — errored or non-first descriptor, net_pkt_rx_alloc() failure, invalid descriptor length, and net_pkt_get_frag() failure — did not, re-arming the ring slot with the write-back residue as its DMA target address. The drop paths are driven entirely by received traffic and need no privilege or special configuration. With the defaults for this driver (CONFIG_NET_BUF_DATA_SIZE of 128 and 16 receive descriptors) a single full-size frame consumes twelve ring slots and twelve K_NO_WAIT fragment allocations, so a short burst of frames sent to the device exhausts the receive pools and reaches the allocation-failure paths; a frame with a receive error, or any frame whose first descriptor was already dropped, reaches the non-first-descriptor path. Once a slot has been poisoned, the DMA writes the next frame received in that slot to an address derived from the frame's VLAN tag fields rather than to a receive buffer. On the supported MCX SoCs that address falls in flash or reserved space, so the transfer raises a fatal bus error that the driver only logs — there is no reset or recovery path — and reception stops permanently until the device is rebooted; where the write is silently discarded instead, the untouched buffer is later handed to the network stack with a length, delivering stale buffer contents as if they were a received frame. A single triggering event is enough to make the condition persistent, so an attacker able to send traffic to the device can permanently disable its network interface.

Is your site exposed to CVE-2026-90591?

Run a free security scan — no signup, results in seconds.

CVSS v3.1 Score

7.5
HIGH
CVSS:3.1/AV:N/AC:L/PR:N/UI:N/S:U/C:N/I:N/A:H

EPSS — Exploit Prediction

0.0028
Probability of exploitation
0.21%
Percentile rank

EPSS estimates the probability that this vulnerability will be exploited in the wild within the next 30 days. A higher score means more likely to be exploited.

Weakness Type (CWE)

CWE-787 Out-of-bounds Write

References

Frequently Asked Questions

What is CVE-2026-90591? +
The NXP ENET-QOS Ethernet driver's receive work handler eth_nxp_enet_qos_rx() in drivers/ethernet/eth_nxp_enet_qos hands each processed descriptor back to the DMA by writing desc->read.control = rx_desc_refresh_flags, which sets OWN_FLAG and BUF1_ADDR_VALID_FLAG. RDES0 of a receive descriptor is the DMA buffer address in read format, but the hardware write-back aliases that word with the VLAN tag fields (or, for a context descriptor, the timestamp low word), so it is destroyed on every completion. The success path rewrites desc->read.buf1_addr before re-arming; the four drop paths — errored or non-first descriptor, net_pkt_rx_alloc() failure, invalid descriptor length, and net_pkt_get_frag() failure — did not, re-arming the ring slot with the write-back residue as its DMA target address. The drop paths are driven entirely by received traffic and need no privilege or special configuration. With the defaults for this driver (CONFIG_NET_BUF_DATA_SIZE of 128 and 16 receive descriptors) a single full-size frame consumes twelve ring slots and twelve K_NO_WAIT fragment allocations, so a short burst of frames sent to the device exhausts the receive pools and reaches the allocation-failure paths; a frame with a receive error, or any frame whose first descriptor was already dropped, reaches the non-first-descriptor path. Once a slot has been poisoned, the DMA writes the next frame received in that slot to an address derived from the frame's VLAN tag fields rather than to a receive buffer. On the supported MCX SoCs that address falls in flash or reserved space, so the transfer raises a fatal bus error that the driver only logs — there is no reset or recovery path — and reception stops permanently until the device is rebooted; where the write is silently discarded instead, the untouched buffer is later handed to the network stack with a length, delivering stale buffer contents as if they were a received frame. A single triggering event is enough to make the condition persistent, so an attacker able to send traffic to the device can permanently disable its network interface. It has a CVSS v3.1 base score of 7.5 (HIGH).
How severe is CVE-2026-90591? +
CVE-2026-90591 has a CVSS v3.1 score of 7.5 out of 10, rated HIGH. This is a high-severity vulnerability that should be prioritized for patching. The EPSS score is 0.0028, placing it in the 0th percentile for exploitation probability.
How do I check if I'm vulnerable to CVE-2026-90591? +
You can use Secably's free Website Scanner to check your website for known vulnerabilities. For infrastructure scanning, use the Port Scanner to identify exposed services that may be affected. Check the vendor advisories linked above for specific patch and version information.

Related Vulnerabilities

Don't wait for an exploit

Scan your website for vulnerabilities like CVE-2026-90591 — free, no signup required.

Patch and protect

Block known exploits with a web application firewall while you patch, keep your own devices clean, or test the fix on a fresh server.

Compare VPS prices →

Affiliate links: we may earn a commission, your price stays the same.