CVE-2026-19576

MEDIUM
Published Oct 11, 2026 Modified Oct 15, 2026 CWE-787

Description

The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured. Each loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte. The impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing.

Is your site exposed to CVE-2026-19576?

Run a free security scan — no signup, results in seconds.

CVSS v3.1 Score

6.8
MEDIUM
CVSS:3.1/AV:P/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H

EPSS — Exploit Prediction

0.0017
Probability of exploitation
0.06%
Percentile rank

EPSS estimates the probability that this vulnerability will be exploited in the wild within the next 30 days. A higher score means more likely to be exploited.

Weakness Type (CWE)

CWE-787 Out-of-bounds Write

References

Frequently Asked Questions

What is CVE-2026-19576? +
The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured. Each loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte. The impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing. It has a CVSS v3.1 base score of 6.8 (MEDIUM).
How severe is CVE-2026-19576? +
CVE-2026-19576 has a CVSS v3.1 score of 6.8 out of 10, rated MEDIUM. This is a medium-severity vulnerability that should be remediated as part of regular maintenance. The EPSS score is 0.0017, placing it in the 0th percentile for exploitation probability.
How do I check if I'm vulnerable to CVE-2026-19576? +
You can use Secably's free Website Scanner to check your website for known vulnerabilities. For infrastructure scanning, use the Port Scanner to identify exposed services that may be affected. Check the vendor advisories linked above for specific patch and version information.

Related Vulnerabilities

Don't wait for an exploit

Scan your website for vulnerabilities like CVE-2026-19576 — free, no signup required.